Thursday, December 31, 2009

Ardubot Arduino

Yeah, programming time!

First step is to download and get the software up and running for the Arduino.  I didn't have any problems, but that might be because I had some other serial and avr stuff already installed.  Some people I believe had do download java or some such other things.

Step two is to hook up the Arduino so that the computer can see it.  Under the tools drop down menu you will need to select 'board' and select which board you are using.  Then you will select 'serial' (also under the tools menu) and select where your board is attached.  There are ways to find out which port your board is attached to but trial and error works too.

Next we are going to start typing, I know I could give you a file to download, but I think you learn more if you type it (although you will probably just copy and paste anyway).  So here is the code

char MLR = 9;  //Left Motor Reverse
char MLF = 6;  //Left Motor Forward
char MRR = 5;  //Right Motor Reverse
char MRF = 3;  //Right Motor Forward

void setup(){
pinMode(MLF, OUTPUT);
pinMode(MLR, OUTPUT);
pinMode(MRF, OUTPUT);
pinMode(MRR, OUTPUT);

void loop(){
digitalWrite(MLF, HIGH);
digitalWrite(MRF, HIGH);
digitalWrite(MLR, HIGH);
digitalWrite(MRR, HIGH);


When its all typed you are going to select the left most icon on top, the one that looks like a play button.  This will compile or verify your program .  At this point make sure your Arduino board it attached to your pcb board. Then select the second to last button (a right arrow) this should upload the program to your Arduino.  After a second or two the Arduino will restart and you should see/hear your motors going.  Now is a good time to unplug the Arduino, once the Arduino is off you can add the wheels.  Don't put the wheel by the USB port all the way on, you still need the USB cable at this point for power.  So try it, see what you've got, and have fun playing with the code

Monday, December 7, 2009

Ardubot Solder

In this step you will need the PCP board, the headers, the power switch, the H-bridge (the IC chip) and your soldering stuff

1.  Break the headers so you have 2 pieces of 6, 2 pieces of 8 and 3 pieces of 2
2.  Solder the pieces of 6 and 8 onto the board in the holes that are labeld
3.  Solder 1 of  the 2 pin pieces in the unlabeled holes next to where the power switch goes
4.  Solder the powerswitch in
5.  Solder the H-bridge in

The silk screening will be on the bottom of your robot.
All pins should be placed so that the smaller end goes through the board, and the longer end is sticking up
The H-bridge goes on the bottom of the board (match up the notch on the board and the chip)

6. Solder the other 2 pin pieces next to the H-bridge facing down
7. Screw the motors onto the bottom of the board with the brakets (brakets are keyed).  Don't attach wheels yet
8. Bend the 2 pin pieces next to the motors so they are near the contacts on the motors
9. Solder the 2 pin pieces to the motors
10. Turn off the soldering iron we are all done soldering (except for the wireless part which comes way later)

Check out sparkfun's tutorial for pictures on correct placement here

Ardubot Parts

The Bot
Arduino - the brains of the robot $29.95
Ardubot PCB Board - the base of the robot $14.99
Wheels - 2 wheels $6.95
Caster - 1 caster $2.95
Motors - need 2 motors $15.95 each
Motor Brackets - set of 2 $4.95
H-bridge motor driver - needed to run the motors $2.35
Power switch - turns battery power on/off $1.50
Headers - their tutorial says 2 but I only used 1 $2.50
Battery Holder - regulated battery holder, 5V $10.95

Wireless Stuff
xbee - this is the wireless module, you will need 2 $22.95each
xbee explorer - this connects your xbee to your computer $24.95
xbee explorer regulated - the connects your xbee to your bot $9.95

Other stuff
computer with usb
usb a-b cable
usb a-mini b cable
soldering iron/ solder
wirecutters/ wirestrippers

Look, I have an Ardubot

So sparkfun was suppose to have a robot class and competition this past weekend, they ended up getting canceled and morphed into more of a workshop.  Lucky for me I got to go.  In about 4 hours I had a arduino bot up and running by remote control on my netbook.  So, I'm going to go through and do another tutorial and once again it might take me a while to get through it...

Ardubot Parts
Ardubot Solder
Ardubot Arduino
Ardubot Battery
Ardubot Wireless